HG50 Tube Mill

Brand:TD

Description:I. Summary The mill is intended for manufacturing of round pipe of Φ12.7mm-Φ50mm with thickness of 0.8mm–3.0mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths. Finished product will be of round, square or rectangular pipe. II. The technical flow of the production line {SteelTape}→→ Double-head un-coiler →→Strip-head Cutter and welder→→ Spiral accumulator→→Forming section（Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller）+ Removing External and internal burr →→Eddy Current Tester→→Zinc Painting Machine→→Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table

Origin:China Hebei

Model:HG50 Tube Mill

MOQ:HG50 Tube MillSets

FOB:perSets120500--126860USD

Port:tianjin

Packaging Details:seaworthy packing way

Product detail: HG50 Tube Mill/pipe mill/pipe machine/tube machine/tube making machine/pipe making machine/ERW Straight seam pipe mill/ERW Straight seam pipe machine/tube mill equipment
www.tengdimc.com
I. Summary

The mill is intended for manufacturing of round pipe of Φ12.7mm-Φ50mm with thickness of 0.8mm–3.0mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.

Finished product will be of round, square or rectangular pipe.

II. The technical flow of the production line

{SteelTape}→→ Double-head un-coiler →→Strip-head Cutter and welder→→

Spiral accumulator→→Forming section（Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller）+ Removing External and internal burr →→Eddy Current Tester→→Zinc Painting Machine→→Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table

III. Basic conditions: 

a) Steel Pipe Specification

1. Pipe diameter:              Ø12.7–Ø50mm 

Pipe Thickness:             0.8– 3.0mm

2. Square Pipe:               10X10mm –40X40mm

Rectangle Pipe:             10X20mm –30X50mm

Pipe Thickness:             0.8 – 2.0mm

3. Pipe Length:                6-9m 

4. Length Tolerance:           0-6mm 

b) SteelTape Specification

1. Material:         Low Carbon steel (δb≤500Mpa, δs≤235Mpa)

2. Steel Tape: Inner diameter:    Φ510-Φ610mm

Outer diameter:    Φ900-1500mm

Strip steel width:    40mm-160mm

Strip steel thickness: 0.8mm-3.0mm

The maximum weight: 3.0 tons

c) Electricity

1. Dynamic power:  AC380V±10%, 3phases, 50Hz±1.0%

2. Control Power:  AC220V±10%, one phase, 50Hz ±1.0%

d) Electric installed capacity:       appro. 450KW

e) Cooling water

 1. Reservoir for High Frequency equipment:  15 m³, one set

 2. Reservoir for circulating cooling water:     15 m³, one set

f) Compressed air

1. Pressure:   0.4Mpa

2. Flow:       0.5m3/h

g) Production capacity

Annual output:  10000 ton, according to the yearly working days、daily working hours and the products. 

h) Line speed:  30-90m/min