Condensation Silicone Rubber in Mold Making

Brand:aa

Product detail:

Description of Condensation Silicone Rubber in Mold Making 

 

Condensation Silicone Rubber in Mold Making is a kind of  two-component material, and the silicone rubber includes Part A base silicone and Part B CA30 curing agent. The Part A base silicone and Part B curing agent can cure at room temperature by a condensation reaction. These materials can be cast into the cured silicone mold: plaster, polyurethane, PU, GRC, cement, resin, polyester, wax etc...

 

Specifications of MC Liquid Silicone Rubber

  

Room Temperature Vulcanization

Equipped with REACH certificate

Professional technician with rich experience

4% catalyst offers for free of charge

Silicone hardness range: 10-60 shore A

High duplicating silicone molds

 

Features of Condensation Silicone Rubber in Mold Making 

 

1. Good flow ability and long working time

2. Medium hardness

3. High tear and tensile strength

4. Easy de-mould from complex replica parts

5. Acid and alkali-resistance

6. Low linear shrinkage

 

Applications of Condensation Silicone Rubber in Mold Making 

    

liquid silicone rubber for mold making can be applied in many objects mold making, since MC liquid silicone rubber has good flow ability and medium hardness, and the silicone can cure at room temperature, thus it's a good material for duplication.

 

Liquid Silicone Rubber can be used for artificial stone mold making. For example,RTV2030, RTV2066 and RTV2088 silicone.

  

Liquid silicone rubber can be applied in candle and soap mold making, such as RTV215 and RTV218 silicone.

  

Liquid silicone rubber can be used for plaster mold making, such as RTV2025, RTV2028 and RTV2030 silicone.

  

Liquid silicone rubber can be applied in the field of shoe sole mold making, for example, RTV3010 and RTV3015 silicone.

 

Liquid silicone rubber can be used for prototyping and electronic potting.

  

Liquid Silicone Rubber is suited for reproduction of cement molding, concrete stones, artificial stones, plaster molding, figures, art objects, decoration molding, GRC products, gypsum products, resin products, PU molds. Etc.

  

Instructions for Making Silicone Molds

 

1. Preparing

 

The surface of the original objects should be clean and free of loose material. If your products have thin flower patterns, and especially have porous substrates, please use a suitable mold release agent such as soap water, detergent, Vaseline or petroleum jelly.

  

2. Mixing

 

Please weigh Part A silicone base and part B CA30 Curing Agent with ratio of 100:2 into a clean container. Stir Part A base silicone thoroughly before use, then Mix Part A and Part B evenly until the curing agent completely dispersed in the silicone base. Manual or mechanical mixture can be used, but do not last much time or allow the temperature to exceed 35°C (95°F).it’s suitable to mix small quantities to ensure thorough mixture of silicone base and curing agent.

 

Note: It is strongly recommended that entrapped air be removed in a vacuum chamber, allowing the mixture to completely expand and then collapse. After a further 1 to 2 minutes under vacuum, the mixture should be inspected and can be used if free of air bubbles. A volume increase of 3-5 times will occur on vacuum de-airing the mixture. So a suitably large container should be chosen.

 

3. Pouring and curing

 

Pour the mixed Part A base silicone and CA-30 curing agent as soon as possible onto the original object, avoiding air entrapment. The catalyzed material will cure to a flexible rubber within 6 hours (or faster by different mixing ratio or room temperature), we advice you de-mold after 24 hours, it is will improve the replicate times of silicone mold.

  

Storage of Condensation Silicone Rubber in Mold Making 

 

When the Liquid Silicone Rubber is stored at or below 30 °C(85 °F) in the original unopened containers, RTV2 Silicone Base and CA30 Curing agent have a usable life of 12 months from the date of production. After 12 months,please use the stirring mill to stir  the Part A silicone for some minutes, then the silicone rubber can be use again, no influence for other performance.

 

  

The information above is just for reference, if you're interested or have any questions, please feel free to contact Nicole:

Web:www(dot)mcsilicone(dot)com

E-mail:nicole(at)mcsilicone(dot)com

Skype:nicoleszmc

MSN: nicoleszmc (at)hotmail(dot)com