Verified Company
Nanning V-Can Business Co., Ltd.
Click to enlarge
V-CAN V-REFLEXTM REFLECTIVE MATERIAL
TF-HW256025 Iron On Transfer
iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/
Product
V-REFLEX™ TF-HW256025 iron on transfer is designed for use on safety garments and casual wear. When properly used, TF-HW256025 Iron on silver reflective film for garment help enhance the visibility of the wearer in nighttime or low-light conditions when illuminated by a light source such as headlights, by returning the light back toward the original source and reaching the automobile driver’s eye.
iron on transfer / iron on transfer/ iron on transfer/ iron on transfer
V-REFLEX™ TF-HW256025 iron on transfer exceeds the minimum reflectivity requirements of EN471 Level 2.
Our product value | EN471 Minimum requirement | Entrance Angle | Observation Angle |
510 | 330 | 5 | 0.2 |
373 | 250 | 5 | 0.33 |
41.7 | 25 | 5 | 1 |
27.7 | 10 | 5 | 1.5 |
486 | 290 | 20 | 0.2 |
356 | 200 | 20 | 0.33 |
50.5 | 15 | 20 | 1 |
28.3 | 7 | 20 | 1.5 |
428 | 180 | 30 | 0.2 |
323 | 170 | 30 | 0.33 |
49.3 | 12 | 30 | 1 |
30.1 | 5 | 30 | 1.5 |
293 | 65 | 40 | 0.2 |
245 | 60 | 40 | 0.33 |
32.2 | 10 | 40 | 1 |
25.3 | 4 | 40 | 1.5 |
Physical Performance
V-REFLEX™ TF-HW256025 Iron on silver reflective film for garment transfer film will meet or exceed the following physical performance as noted. All RA values are at +5° entrance angle and 0.2° observation angle.
Physical Performance | Test Method |
Retro Reflectivity : (Initial) | ANSI/ISEA 107-2010 Level 2 |
Abrasion : RA ≥ 100 | 5000 Cycles (EN 530 Method 2) |
Flexing : RA ≥ 100 | 7500 Cycles (ISO 7854 Method A) |
Cold Fold: RA ≥ 100 | -20 °C (-4 °F)( ISO 4675) |
Temperature Cycle : RA ≥ 100 | 12 hours @ 50 °C (122 °F); 20 hours @ -30 °C (-22 °F) |
Wash : RA ≥ 100 | 25 cycles @ 60 °C ( ISO 6330) |
Flame Resistance4 : char length ≤ 4 inches | Flame ≤ 2 seconds |
Heat Resistance4 : cannot melt drip, separate or ignite | 5 minutes @ 260°C (500 °F) |
Convective Heat4 : RA ≥ 100 | 10 minutes @ 140 °C (285 °F) |
Application
Cutting
Die-cutting is recommended ,although it can also be hand-cut or guillotined
iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ on transfer / iron on transfer / iron on transfer / iron on transfer / iron on transfer / iron on transfer/ iron on transfer
Application Instructions
V-REFLEX™ TF-HW256025 TF-HW256025 iron on transfer is used together on a single flat surface or as a set where uniform heat and pressure can be applied.
Avoid applying film over seams and stitches
Remove adhesive side liner,exposing dry adhesive. Do not remove reflective side liner.
Place the product on substrate with the adhesive side down and apply heat and pressure.
Precautions for Heat Lamination
Do not exceed lamination temperatures listed below as the paper liner may become difficult to remove. If high temperatures are required for bond durability, follow lamination steps 1-3 using recommended temperature, remove paper liner, and then laminate again at the higher temperature (using a non-stick slip sheet to protect reflective surface).
| TF-HW256025 iron on transfer | |||||
| Item NO. | Adhesive side Liner | Reflective Side Liner | Temperature | Dwell Time(seconds) | Line Pressure |
| TF-HW256025 | None | PET | 167-177 °C (325-350 °F ) | 10-20 | Firm(30-40psi) |
Care & Maintenance
| Max. wash Temp. | Dry | Iron Temp. | Dry Clean |
| Machine wash hot 60 °C (140 °F ) | Tumble dry low | Cool iron 110°C(230 °F ) |
25 cycle,ISO3175 |
iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/ iron on transfer/