Hotspot Zte Mf60,Unlocked Zte Mf60

ZTE MF60 WiFi hotspot is a 3.5G mobile hotspot device, working in GSM/GPRS/EDGE/WCDMA/HSPA+ network. The client device could connect to it via USB or Wi-Fi interface. With HSDPA 21Mbps downlink, quad-band GSM and tri-band UMTS, it gives maximum 8 users super fast Internet experience all over the world at the same time.
It runs on battery and has a mini USB port and a built-in OLED display on the top and could supports up to 32GB Micro SDHC memory. The device supports data and SMS services, enabling you to communicate anytime and anywhere.

Highlight:

 This HSDPA device is peak rated at 21 Mbps downlink speed.
Operates on the 3G networks for wireless access to e-mail and internet on the move.
Use 802.11b/g Wi-Fi connection so no installation is required. Simply enter the password key supplied and get on line   immediately with your Next G'SIM.

 Small, light weight design. 

 Supports three working modes: USB Mode, Wi-Fi Mode, Mixed Mode.

Specification:
Data service:
 HSDPA/HSUPA/UMTS 850/1900/2100 MHz
 GSM/GPRS/EDGE 850/900/1800/1900 MHz
 HSPA: DL 21.6Mbps, UL 5.76Mbps
WCDMA CS: 64Kbps UL/DL
WCDMA PS: 384Kbps UL/DL

Interface: USB and Wi-Fi
Wi-Fi Security: WEP/WPA/WPA2/WAPI
USB Version: USB 2.0 high speed
USB Interface Type: Micro USB
 MicroSD card: ZTE MF60 supports up to 32GB microSD card

Battery:
Power Adapter: 5V/700m A Battery: 1500mAh
 Standby time: 100 hours
Working time: 4 hours

Features:
 Weight: 77g
 Dimensions(W x h x D): 99.7mm*53.7mm*13.9mm

Other requirements:
 Operating temperature: 0°C~+35°C
 Storage temperature: -20°C~+50°CCharging temperature: 0°C~45°C
Operate System: Windows 7, Windows Vista(32bit or 64bit), Windows XP(SP2 or later), MAC(10.4 or later)
Web Brower: IE(6.0 or later), Firefox(2.0 or later), Opera(10.0 or later), Safari(4.0 or later), Chrome(5.0 or later)

Notes:
1. MocroSD is a trademark of SD Card Association
2. The ZTE MF60 hotspot’s standby and working time are only for you reference, and based on ideal working environment.

Getting to Know the Device
The following figure shows the appearance of the device.

1. Power: Hold the Power button to switch on/off the device
2. Memory card slot (microSD card): it is where you insert the memory card(MicroSD card)
3. WPS
This button is used to start/end Wi-Fi Protected Setup authentication process and enable/disable the Wi-Fi function
Hold it for 3 seconds to activate the WPS function
 When the WPS function is available, press it to deactivate the WPS function
 Press it to enable/disable Wi-Fi function
4. LED Screen: It indicates the signal type, signal strength, battery, Wi-Fi, etc.
5. External Antenna Connector: it is used to connect an external antenna to enhance the signal strength.
6. Charger/USB port:
a. Charge your device.
b. Connect the client to your device via USB cable.

Notes:Hold the WPS and Power buttons simultaneously until the LED screen turns off, and then release the buttons. The ZTE MF60 3G Router will restart automatically and restore to the factory default settings.